RAM X-Grip Pipe Clamp Mount for 9-11 Tablets Setup

By RAM® Mounts | Best Phone, Tabletand Laptop Mounts for Cars and ... | Published: 2026-10-19

Category: How-to Guides

Step-by-step guide to installing the RAM X-Grip with Tough-Claw pipe mount for 9-11 inch tablets. Avoid common mistakes and get a secure fit.

Quick Answer

To set up the RAM X-Grip with Tough-Claw pipe mount for a 9-11 inch tablet, clamp the Tough-Claw onto a suitable pipe, attach the X-Grip holder, and adjust the arms for a snug fit without over-tightening.

Choosing the Right Pipe and Location

The Tough-Claw clamp works on pipes with diameters from 0.75 to 2.5 inches. Ensure the pipe is sturdy enough to support the weight of your tablet (up to about 2 lbs for most 9-11 inch models). Avoid mounting on thin or hollow pipes that could bend or vibrate.

For vehicles, a roll bar, grab handle bracket, or seat frame tube works well. On a boat, a fishing rod holder or T-top rail is ideal. In a workshop, a horizontal or vertical pipe on a rack or stand provides a solid base.

Understanding the X-Grip Holder's Range

The X-Grip holder included in this mount is designed for tablets 9 to 11 inches diagonally. It uses four spring-loaded rubber arms that expand to grip the device. The arms can accommodate tablets with or without a slim case, but very thick protective cases may interfere with the grip.

If your tablet has buttons or ports on the sides, you can rotate the holder 360 degrees using the socket arm to position the tablet for easy access.

Installation Steps

1. Open the Tough-Claw Clamp: Turn the knob counterclockwise to loosen the clamp jaws until they are wide enough to fit around your chosen pipe. Slide the clamp onto the pipe at the desired location. Common mistake: Forgetting to check pipe diameter compatibility (0.75-2.5 inches) before mounting. Measure your pipe first.
2. Tighten the Clamp Securely: Turn the knob clockwise to tighten the clamp onto the pipe. Use the built-in T-handle to get a firm hand-tight grip. Do not use tools to over-tighten, as this can damage the clamp or pipe. Checkpoint: The clamp should not slide or rotate on the pipe when you apply moderate force. If it moves, tighten more.
3. Attach the X-Grip Holder to the Ball Base: The Tough-Claw clamp has a 1-inch ball on its top. Push the X-Grip holder's socket arm onto the ball until it clicks. Tighten the knob on the socket arm to lock the angle. Common mistake: Not tightening the socket arm enough, which allows the tablet to sag or rotate. Ensure the knob is snug.
4. Adjust the X-Grip Arms for Your Tablet: Pull the four rubber arms outward to open the holder. Place your tablet centered on the back pad, then press the arms inward one by one until they grip the edges firmly. The arms should hold the tablet without excessive pressure. Checkpoint: The tablet should not wobble, but the arms should not feel overly tight. If the tablet slides out, tighten the arms slightly by pushing them further inward.
5. Final Positioning and Test: Rotate the tablet to your preferred viewing angle using the socket arm. Test the mount by gently shaking the tablet to ensure it is secure. If needed, re-tighten the clamp or socket arm. Common mistake: Mounting the tablet in a position that blocks essential controls or vents. Adjust before finalizing.

Product Details

RAM® X-Grip® with RAM® Tough-Claw™ 9" Pipe Mount for 9"-11" Tablets: The RAM X-Grip with Tough-Claw 9" Pipe Mount securely holds tablets sized 9" to 11" and includes the X-Grip holder and Tough-Claw clamp. This all-in-one kit saves you from buying separate components, and the clamp fits a wide range of pipe diameters for flexible mounting options.
RAM® X-Grip® with RAM® Tough-Claw™ 9" Pipe Mount for 9"-11" Tablets